World Library  
Flag as Inappropriate
Email this Article

DC component

Article Id: WHEBN0003578576
Reproduction Date:

Title: DC component  
Author: World Heritage Encyclopedia
Language: English
Subject: Capacitive coupling, Line code, White noise, TDMoIP, Unipolar encoding, MIL-STD-1553
Publisher: World Heritage Encyclopedia

DC component

When describing a periodic function in the frequency domain, the DC bias, DC component, DC offset, or DC coefficient is the mean value of the waveform. If the mean amplitude is zero, there is no DC offset. In contrast, various other frequencies are analogous to superimposed AC voltages or currents, hence called AC components or AC coefficients.

The term originated in electronics, where it refers to a direct current voltage, but the concept has been extended to any representation of a waveform. The term's use is extended to two-dimensional transformations like the discrete cosine transform used in JPEG.

A waveform without a DC component is known as a DC-balanced waveform. DC-balanced waveforms are useful in communications systems to avoid voltage imbalance problems between connected systems or components.

DC offset is usually undesirable when it causes saturation or change in the operating point of an amplifier. An electrical DC bias will not pass through a transformer; thus a simple isolation transformer can be used to block or remove it, leaving only the AC component on the other side. In signal processing terms, DC offset can be reduced in real-time by a high-pass filter. When one already has the entire waveform, subtracting the mean amplitude from each sample will remove the offset. Often, very low frequencies are called "slowly changing DC" or "baseline wander".

Practical applications

A DC tape bias was used in early tape recorders to reduce distortion.

A DC bias is applied to the control grid of vacuum tubes in power amplifiers in order to regulate power.[1]

DC-balanced signals are used in communications systems to prevent bit errors when passing through circuits with Capacitive coupling or transformers. Bit errors can occur when a series of 1's create a DC level that charges the capacitor of the high-pass filter used as the AC coupler, bringing the signal input down incorrectly to a 0-level. In order to avoid these kinds of bit errors, most line codes are designed to produce DC-balanced waveforms. The most common classes of DC balanced line codes are constant-weight codes and paired-disparity codes.

Remote power

Main article: Phantom power

A DC bias can be used to power microphones or other devices over the same wires as required for the signal. This is commonly used, for example, in professional audio microphones.

On modern satellite dishes, used for direct-broadcast satellite TV, a DC bias is used to provide electrical power to the feedhorn. Changing the bias between approximately 12 and 18 volts also allows selection of the correct polarization (horizontal and vertical on older systems, clockwise and counterclockwise on newer circular polarization systems).

Frequency selection

On a voltage-controlled oscillator (VCO), such as in a radio transmitter, selection of the center frequency of the carrier wave is done with a DC bias. For frequency modulation (FM), the AC component is the baseband audio signal plus any subcarriers. Frequency-shift keying can be done solely by changing the DC bias.

Electrical grid

The electrical grid, which is normally three-phase AC, can be severely disrupted by the presence of a large DC bias. This is caused by strong solar flares hitting the Earth's atmosphere, which in turn creates strong electromagnetic fields. This induces voltages in long-distance electrical lines, which can be strong enough to arc across transformers. (Even pipelines, such as the mostly above-ground Alaska Pipeline, are prone to this, and must be tied to electrical ground with zinc sacrificial anodes.) This is a rare but serious problem, mostly for far northern locations like Canada and Scandinavia, where a strong aurora borealis will cover much lower latitudes than normal during such a situation. Space weather forecasts are used to predict when these geomagnetic storm events might occur. High-voltage direct current systems have their own control gear at conversion stations and can adapt somewhat better to such conditions, however large and often widely-fluctuating voltages can still cause problems like harmonics.

See also

Electronics portal
Energy portal


This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.