World Library  
Flag as Inappropriate
Email this Article

Churchill tank

Tank, Infantry, Mk IV (A22)
Tank, Infantry Mk IV Churchill IV (75mm)
Type Infantry tank
Place of origin United Kingdom
Service history
In service 1941–52 (British Empire)[note 1]
Used by United Kingdom
Soviet Union
Production history
Designer Harland and Wolff (A20)/ Vauxhall Motors (A22)
Manufacturer Vauxhall Motors
Produced 1941 to 1945
Number built 7,368 (all types together)
Variants See below
Weight 38.5 t (37.9 long tons)
Length 24 ft 5 in (7.44 m)
Width 10 ft 8 in (3.25 m)
Height 8 ft 2 in (2.49 m)
Crew 5 (commander, gunner, loader/radio operator, driver, co-driver/hull gunner)

Armour 16 to 102 mm (In the MK VII front armour 152 mm)
QF 2 pdr (early Marks)/Ordnance QF 75 mm (later Marks)
2 × 7.92 mm Besa machine guns
Engine Bedford horizontally opposed twin-six petrol engine
350 hp (261 kW) at 2,200 rpm
Power/weight 9.1 hp/tonne
Transmission Merritt-Brown 4-speed constant-mesh epicyclic gearbox
Suspension Coiled spring
56 miles (90 km)
Speed 15 mph (24 km/h)
Triple differential steering in gearbox

The Tank, Infantry, Mk IV (A22) was a British heavy infantry tank used in the Second World War, best known for its heavy armour, large longitudinal chassis with all-around tracks with multiple bogies, and its use as the basis of many specialist vehicles. It was one of the heaviest Allied tanks of the war.

The origins of the design lay in the expectation that war in Europe might be fought under similar conditions to those of the First World War, and emphasized the ability to cross difficult ground. The Churchill was rushed into production to build up British defences against a possible German invasion. The first vehicles had flaws that had to be overcome before the Churchill was accepted for wide use. After several Marks had been built a better armoured version, the Mark VII, entered service.

The Churchill was used by British and Commonwealth forces in North Africa, Italy and North-West Europe. In addition, a few hundred were supplied to the USSR and used on the Eastern Front.


  • Name 1
  • History 2
    • A20 2.1
    • A22 2.2
  • Design 3
  • Service history 4
    • Dieppe Raid 4.1
    • North Africa 4.2
    • Italy 4.3
    • North-West Europe 4.4
    • Other theatres 4.5
    • Korean War and after 4.6
    • USSR 4.7
    • Irish Army Service 4.8
  • Variants 5
    • Tanks 5.1
    • Specialist vehicles 5.2
      • Churchill Oke 5.2.1
      • Churchill AVRE (Armoured Vehicle Royal Engineers) 5.2.2
      • Churchill ARV (Armoured Recovery Vehicle) 5.2.3
      • Churchill ARK (Armoured Ramp Carrier) 5.2.4
      • Churchill bridgelayer 5.2.5
      • Churchill Crocodile 5.2.6
      • Gun Carrier, 3in, Mk I, Churchill (A22D) 5.2.7
      • Churchill Flail FV3902 or Toad 5.2.8
      • Churchill Goat 5.2.9
      • Churchill Great Eastern Ramp 5.2.10
      • Churchill Kangaroo 5.2.11
    • Designs based on chassis 5.3
  • Operators 6
  • Preserved examples 7
  • See also 8
  • Notes 9
  • References 10
  • External links 11


There is some ambiguity regarding who the tank is named after. It may have been named after Winston Churchill,[1] who was Prime Minister of the United Kingdom and Minister of Defence at the time, and had been involved with the development of the tank as a weapon during the First World War. Alternatively, and fitting in with other British tank names, it may have been named after John Churchill, 1st Duke of Marlborough, an ancestor of Winston Churchill and the leader of the British Army in the War of the Spanish Succession.



Initially specified before the outbreak of the Second World War the (General Staff designation) A20 was to be the replacement for the Matilda II and Valentine infantry tanks. In accordance with British infantry tank doctrine and based on the expected needs of World War I-style trench warfare, the tank was required to be capable of navigating shell-cratered ground, demolishing infantry obstacles such as barbed wire, and attacking fixed enemy defences; for these purposes, great speed and heavy armament were not required.

The vehicle was specified initially to be armed with two QF 2 pounder guns each located in a side sponson, with a coaxial BESA machine gun. A third BESA and a smoke projector would be fitted in the front hull. The specification was revised to prefer a turret with 60 mm of armour to protect against ordinary shells from the German 37 mm gun. Outline drawings were produced based on using the A12 Matilda turret and the engine of the Covenanter tank. Detail design and construction of the A20 was given to the Belfast shipbuilders Harland and Wolff who completed four prototypes by June 1940. During the construction period the armament was reconsidered which including fitting either a 6 pounder or a French 75 mm gun in the forward hull. In the end a 3-inch howitzer was chosen.[2][3] The A20 designs were short-lived however, as at roughly the same time the emergency evacuation of the British Expeditionary Force from Dunkirk occurred.

At 43 tons, with a 300 hp flat-12 Meadows engine, the A20 had limited power compared to the 18-ton Covenanter.[4] This was a less serious limitation than it might appear, owing to the British distinction between the high-speed cruiser tanks and the slow-speed infantry tanks. Vauxhall were approached to see if they could build the A20 and one example was sent to Vauxhall at Luton to see if they could provide an alternative engine. To this end they developed a flat-12 petrol engine.[5] For speed of production, this engine was based on a Bedford six-cylinder lorry engine, giving rise to its name of "Twin-Six".[4] Although still a sidevalve engine, the engine was developed with high squish pistons, dual ignition and sodium-cooled exhaust valves in Stellite seats to give 350 bhp.[4]


With France lost, the scenario of trench warfare in Northern Europe was no longer applicable and the design was revised by Henry Merritt,[note 2] Director of Tank Design at Woolwich Arsenal, based on the combat witnessed in Poland and France. These new specifications, for the A22 or Infantry Tank Mark IV, were given to Vauxhall in June 1940.[6]

With German invasion of Britain looking imminent, and the loss of a substantial amount of military vehicles in the evacuation from France, the War Office specified that the A22 had to enter production within a year. By July 1940 the design was complete and by December of that year the first prototypes were completed; in June 1941, almost exactly a year as specified, the first Churchill tanks began rolling off the production line.

A leaflet from the manufacturer was added to the User Handbook saying:

Fighting vehicles are urgently required, and instructions have been received to proceed with the vehicle as it is rather than hold up production. All those things which we know are not as they should be will be put right.

The document then described known faults, with work-rounds and what was being done to correct the problem.

Because of its hasty development, there had been little testing, and the Churchill was plagued with mechanical faults. Most apparent was that the Churchill's engine was underpowered, unreliable, and difficult to access for servicing. Another serious shortcoming was the tank's weak armament, the 2 pounder (40 mm) gun, which was improved by the addition of a 3-inch howitzer in the hull to deliver an HE shell, albeit not on a howitzer's usual high trajectory.

Production of a turret to carry the QF 6 pounder gun began in 1941, but problems with the plate used in an all-welded design led to an alternative cast turret also being produced. These formed the distinction between Mark III and Mark IV.[7]

The poor performance of the Churchill nearly caused production to be ceased in favour of the forthcoming Cromwell tank; it was saved by the successful use of the Mk III at the Second Battle of El Alamein in October 1942.

The second major improved Churchill, the Mk VII, was first used in the Battle of Normandy in 1944. The Mk VII improved on the already heavy armour of the Churchill with a wider chassis and the British 75 mm gun which had been introduced on the Mk VI. It was primarily this variant, the A22F, which served through the remainder of war. It was re-designated A42 in 1945.

The Churchill was notable for its versatility and was utilized in numerous specialist roles.


Churchill tanks of 9th Royal Tank Regiment during an exercise at Tilshead on Salisbury Plain, 31 January 1942.

The hull was made up of simple flat plates which were initially bolted together and were welded in later models. The hull was split into four compartments: the driver's position at the front, then the fighting compartment including the turret, the engine compartment, and the gearbox compartment. The suspension was fitted under the two large "panniers" on either side of the hull, the track running over the top. There were eleven bogies either side, each carrying two 10-inch wheels. Only nine of the bogies were taking the vehicle weight normally, the front coming into play when the vehicle nosed into the ground or against an obstacle, the rear acting in part as a track tensioner. Due to the number of wheels, the tank could survive losing several without much in the way of adverse effects as well as traversing steeper terrain obstacles. As the tracks ran around the panniers, escape hatches in the side could be incorporated into the design. These were retained throughout the revisions of the Churchill and were of particular use when the Churchill was adopted as the AVRE.

The Bedford Vehicles engine was effectively two engines in horizontally opposed configuration ("flat twelve") on a common crankshaft. There were four Solex carburettors each on a separate manifold that fed three cylinders formed as a single cylinder head. The elements of the engine and ancillary components were laid out so they could be reached for maintenance through the engine deck covers. Air for the engine was drawn from the fighting compartment through air cleaners. Cooling air was drawn into the engine compartment through louvres on the sides, across the radiators and through the engine compartment by a fan driven by the clutch. This fan blew the air over the gearbox and out the rear of the hull. By opening a flap between the fighting compartment and the engine compartment this airflow could be used to remove fumes produced by firing the armament. The 1,296 cu in (21.238 L) capacity engine was rated at 350 bhp at 2,000 rpm delivering 960 lb·ft (1,300 N·m) over an engine speed range from 800 to 1,600 rpm.

The gearbox featured a regenerative steering system that was controlled by a tiller bar instead of the more commonplace brake levers, or as with the German Tiger I heavy tank, a steering wheel. The tiller was connected with servo assistance, hydraulically to the steering brakes. The Churchill was also the first tank to utilise the Merritt-Brown gearbox, which allowed the tank to be steered by changing the relative speeds of the two tracks; this effect became more pronounced with each lower gear, ultimately allowing the tank to perform a "neutral turn" when no gear was engaged, where it could fully pivot within its own length. There were final reduction gears, of the planetary type, in the driving wheels.

The first turrets were of cast construction and were rounded in shape, providing sufficient space to accommodate the relatively small 2 pounder gun. To fulfil its role as an infantry support vehicle the first models were equipped with a 3 inch howitzer in the hull in a layout very similar to the French Char B. This enabled the tank to deliver a useful high-explosive capability while retaining the antitank capabilities of the 2 pounder. However, like other multi-gun tanks, it was limited by a poor fire arc - the entire tank had to be turned to change the aim of the hull gun. The Mk II dispensed with the howitzer and replaced it with a bow machine gun and on the Mk III, the 2 pounder was replaced with the 6 pounder, significantly increasing the tank's anti-tank capabilities. The tank underwent field modification in North Africa with several Churchills being fitted with the 75 mm gun of destroyed M4 Shermans. These "NA75" variants were used in Italy. The use of the 75 mm, which was inferior as an anti-tank weapon to the 6 pounder but better as an all-around gun, was soon made standard on successive versions.

Churchills made use of the Vickers Tank Periscope MK.IV. In the Mark VII, the driver had two periscopes as well as a vision port in the hull front that could be opened. The hull gunner had a single periscope as well as the sighting telescope on the BESA mounting. In the turret the gunner and loader each had single periscope and the commander had two fitted in his hatch cupola.

The armour on the Churchill, often considered its most important feature, was originally specified to a minimum of 16 millimetres (0.63 in) and a maximum of 102 millimetres (4.0 in); this was increased with the Mk VII to a range from 25 millimetres (0.98 in) to 152 millimetres (6.0 in). Though this armour was considerably thicker than its rivals (including the German Tiger I tank, but not the Tiger II) it was not sloped, reducing its effectiveness. Earlier models were given extra armour by the expedient of welding extra plates on.

On the Mark VII, the hull front armour was made up of a lower angled piece of 5.5 in (140 mm), a nearly flat 2.25 in (57 mm) plate and a vertical 6 inch plate. The hull sides, were for the most part, 3.75 in (95 mm). The rear was 2 in (51 mm) and the hull top 0.525 in (13.3 mm). The turret of the Mark VII was 6 in (150 mm) to the front and 3.75 in (95 mm) for the other sides. The turret roof was 0.79 (20 mm) thick. Plate was specified as IT 80, the cast sections as IT 90.[8]

The A22F, also known as "Heavy Churchill" was a major revision of the design. The most significant part was the use of welding instead of riveted construction. Welding had been considered earlier for the Churchill but until its future was assured this was no more than testing techniques and hulls at the firing ranges. What welding reduced in the overall weight (estimates were around 4%), the thicker armour of the A22F made up for. Welding also required fewer man-hours in construction. The hull doors changed from square to round which reduced stresses. A new turret went with the new hull. The sides, which included a flared base to protect the turret ring, were a single casting while the roof which did not need to be so thick was a plate fitted to the top.[9]

Since the engines on the Churchill were never upgraded, the tank became increasingly slower as additional armour and armament was equipped and weight increased; while the Mk I weighed 39,120 kg (40 long tons) and the Mk III weighed 39,630 kg, the Mk VII weighed 40,640 kg. This caused a reduction in maximum speed of the tank from its original 26 km/h (16 mph) down to 20.5 km/h (12.7 mph). The engines also suffered from many mechanical problems.

Another problem was the tank's relatively small turret that prevented the use of powerful weapons; definitive versions of the tank were armed with either the QF 6 pounder or the derivative QF 75 mm gun. The 6-pdr was effective against armoured vehicles but less so against other targets; the 75mm a better all-round weapon but lacking in effectiveness against armour. Although the Churchills with their 6 pounders could outgun many contemporary German medium tanks (like the Panzer IV with the short-barrel 75 mm gun and the Panzer III's 50 mm gun) and the thick armour of all Churchill models could usually withstand several hits from any German anti-tank gun, in the later years of the war the German Panther tank had a 75 mm high-velocity cannon as its main armament along with increased protection, against which the Churchills' own guns often lacked sufficient armour penetration to fight back effectively.

The Churchill had many variations, including many specialised modifications. The most significant change to the Churchill was that it was up-gunned from 2 pounder to 6 pounder and then 75 mm guns over the course of the war. By the war's end, the late model Churchill Mk VII had exceptional amounts of armour – considerably more than the German Tiger tank. However, the firepower weakness was never fully addressed. The Mark VII turret that was designed for the 75 mm gun was of composite construction – cast with top and bottom plates welded into position.[6]

While it had weaknesses, the Churchill could cross terrain obstacles that most other tanks of its era could not. This capacity frequently proved useful, especially during the fighting in Normandy. One action in Normandy where the tank's ability to surmount obstacles was found to be of value was the capture of Hill 309 on the 30 and 31 July 1944 (Operation Bluecoat) conducted by VIII Corps.

Service history

Dieppe Raid

Churchill tanks on the Dieppe beach. The "Y"-shaped pipes on the rear decking are exhaust pipe extensions to allow deep wading

The Dieppe Raid was planned to temporarily take control of the French port of Dieppe using a strong force of about 6,000 troops – mostly drawn from inexperienced Canadian units. The operation, codenamed Rutter, would test the feasibility of opposed landings. Nearly 60 Churchill tanks from the Calgary Regiment were allocated to support the infantry and commandos; they would be put ashore by landing craft. Some problems were anticipated and allowed for: waterproofing of the hulls, canvas carpets to aid the tanks crossing the shingle beach, engineer teams to demolish obstacles and a few of the tanks were fitted with flame-throwers.

In the event, the German defences were strong and several tanks in each of the four "waves" were lost on or before reaching the beach. Only fourteen got off the shore and past the sea wall. Although the tanks were effective in engaging the defenders in the town's buildings, their progress was blocked by concrete defences; the demolition teams – killed or pinned on the beach – had not been able to accompany the tanks. Some tanks were able to return to the beach once a withdrawal had been signalled but none were taken off. Nearly 70% of the Canadians were killed, injured or captured and none of the raid's objectives were met other than the secret raid on the radar station on a headland.[10]

North Africa

Churchill MKIII tanks of 'Kingforce' during the 2nd Battle of El Alamein

Six Mk III Churchills (with the 6 pounder) saw action in the Second Battle of El Alamein in October 1942. This detachment, called "Kingforce", supported the attack of 7th Motor Brigade. The Churchills were fired on many times by German anti-tank guns, but only one received more than light damage. One tank was said to have been hit up to 80 times.[11][12]

Kingforce was disbanded after El Alamein – it had been formed to test whether the Churchills could operate in Africa. Instead, a full tank brigade (the 25th Army Tank Brigade) of three regiments[note 3] was sent to Africa, and went into action in February 1943 during the Tunisian campaign.

Churchill tanks took part in containing the German offensive of Operation Ochsenkopf in February – March 1943. At a place called Steamroller Farm two Churchill MKIII tanks of 51 RTR got ahead of their squadron. They came across an entire German transport column which they ambushed and completely shot up before they rejoined. The end result was the destruction of two 88 mm, two 75 mm and two 50 mm, four lesser anti-tank guns, twenty-five wheeled vehicles, two 3 inch Mortars, two Panzer Mark III tanks, and infliction of nearly 200 casualties.[13]

A Churchill tank in a hull down defensive position made a particular contribution to Allied success. In one encounter on 21 April 1943 during the start of the Battle of Longstop Hill a Churchill tank of the 48th Royal Tank Regiment got the better of a German Tiger I heavy tank. A 6 pounder shot from the Churchill lodged between the Tiger's turret and turret ring, jamming the turret and injuring the Tiger crew. The crew abandoned the Tiger, which was subsequently captured by the British. Known as Tiger 131, this Tiger was the first captured by the Western Allies and was particularly useful for intelligence. Tiger 131 has since been restored to full working condition and is now on display at The Tank Museum in the United Kingdom.[14]


North Irish Horse Churchill advancing towards Florence, 23 July 1944.

As the mainstay of the Tank Brigades, which operated in support of the infantry, Churchill units were in operation more often than other tank units.[15]

The "NA75" conversions of Churchill Mark III to carry the US 75 mm gun were used in Italy. As the Churchill proved to be a better gun platform than the Sherman, the effective range of the 75 mm was increased.

North-West Europe

Churchills saw widespread action in Normandy as well as subsequent operations in the Low Countries and into Germany such as the fighting in the Reichswald during Operation Veritable.

Other theatres

In mid-1944, at the request of Britain's War Office, the Churchill was tested by the Australian Army, along with the M4 Sherman. The results were to be used to determine any modifications required for use in the tropics; Matildas were used as a reference point in the tests at Madang, New Guinea. The Churchill was found to be, overall, superior to the other tanks for jungle warfare.[16][17]

It was not used in the Pacific War; only 46 of the 510 Churchills ordered by Australia were delivered by the end of the war. The remainder of the order was cancelled.

Korean War and after

In late 1950, a Churchill Crocodile squadron (C squadron, 7 Royal Tank Regiment) was sent to Korea. In action against the Chinese they mostly fought as gun tanks, for example in the Third Battle of Seoul. To restore 1st Battalion, Royal Northumberland Fusiliers' (1RNF) position during the defence of Seoul, Brigadier Thomas Brodie of the 29th Infantry Brigade sent four Churchill tanks as reinforcement, and their contributions to the battle was widely praised by British and American historians.[18] These were the last use of the Churchill in action by the British. The tank remained in the service of the British Army until 1952 with one, a bridge-layer, remaining in service well into the 1970s.


A Soviet Churchill Mk IV passes a knocked-out German Sd.Kfz 232 (8-Rad) armoured car at the fourth battle of Kharkov in 1943

The Soviet Union was sent a total of 301 Churchill Mk III and Mk IV types as part of the Lend-Lease programme. Forty-three were lost en route on the Arctic Convoys.

Churchills were at the Battle of Prokhorovka (Kursk) in 1943 with the 5th Guards Tank Brigade.

Irish Army Service

The Irish Army took delivery of three Churchill Mk VI tanks in 1948 and a fourth in 1949. They were rented from the British War Office as trials vehicles until 1954, when they were purchased outright. This purchase was despite the fact that the supply and transport corps workshops, who maintained them, had reported that spares had all but run out.[19] Experiments were carried out involving replacing the existing Bedford engine with a Rolls-Royce Merlin engine salvaged from an Irish Air Corps Seafire aircraft. The experiment was not a success, although the reasons are not recorded.[19] By 1967 only one Churchill remained serviceable, and by 1969 all were retired. One remains preserved in the Curragh Camp.


AVRE 290mm Petard Mortar and its ammunition (projectile standing on its flat nose, with tail upmost, at right)

During the course of the war, as well as new production, older vehicles were reworked to bring them up to later standard. For example, 2-pdr turrets were replaced with the 6-pdr turret, and the improved commander's cupola (with eight episcopes) introduced after the first Mark VII was applied to some earlier marks as well. Nearly 3,100 Churchills of all marks were rebuilt.[20] Early tanks were produced before the Churchill name was attached and were retroactively known as Churchill Mark I etc.

Mk I Churchill tank with hull-mounted 3-inch howitzer on exercises on Salisbury Plain, January 1942


With number produced Churchill I (303)

Equipped with a 2 pounder gun in the turret (150 rounds), and a coaxial Besa machine gun. There was a 3 inch howitzer in the hull (58 rounds). It was a tank that was noted for poor mechanical reliability. It was the main tank issued to the Canadian forces at Dieppe. It was used in Tunisia and some were still in use late in the war in Italy on the Gothic Line.[21]
A Churchill MKIII tank

Churchill Mk II (1,127)

Replaced the hull howitzer with another machine gun to reduce cost and complexity. Sometimes referred to as "Churchill Ia."

Churchill Mk IICS (Close Support)

Placed the 2pdr gun in the hull and the howitzer in the turret, available in very limited numbers. Sometimes called "Churchill II" Not used in combat.[20]
Churchill Mk VI tank

Churchill Mk III (675)

The III was the first major armament overhaul of the series, eliminating the hull howitzer and equipping the tank with a more powerful 6 pounder gun (84 rounds). Unlike early versions, it had a welded turret. The first Mark to have "catwalks" over the upper track runs.

Churchill Mk IV (1,622)

The IV was the most numerous Churchill produced, and was virtually identical to the III, the largest change being a return to the less costly cast turret. The Mark V 6 pdr was fitted with a counterweight on early models. Some were retrofitted with 75mm guns (see "NA75", below) from Sherman tanks. Others were up-gunned with British 75mm guns, creating the Mk IV (75).

Churchill Mk V (241)

A Churchill equipped with a close support 95 mm howitzer in place of the main gun (47 rounds) in a cast turret. The turret was similar but not identical to the MkIV/VI turrets with a slightly different opening for the gun in the turret front face.
Tank, Infantry, Mk IV, Churchill VII (A22F) with 75 mm gun

Churchill Mk VI (200)

Along with several minor improvements, e.g. an additional collar at the turret base protecting the turret race, it was produced as standard with the 75 mm Mk V gun. Few were built due to the near release of the VII and current upgunning of the III / IV.
Churchill MKVIII with 95mm Howitzer gun

Churchill Mk VII (A22F) (1,600 with VIII)

The second major redesign from previous models, the VII used the 75 mm gun, was wider and had much more armour. It is sometimes called the Heavy Churchill. This version of the Churchill first saw service in the Battle of Normandy, and was re-designated A42 in 1945.

Churchill Mk VIII

A Churchill VII which replaced the main gun with a 95 mm howitzer (47 rounds) in a slightly different turret.

Refitted previous versions:

Churchill Mk IX

Churchill III / IV upgraded with turret of the VII. Extra armour added along with gearbox and suspension modifications. If the old 6 pounder had been retained, it would have the additional designation of LT ("Light Turret").

Churchill Mk X

The same improvements as for the IX applied to a Mk VI.

Churchill Mk XI

Churchill V with extra armour and Mk VIII turret.

There is no evidence that the Mks IX to XI were ever produced.

Churchill NA75 (200)

Churchill IVs with 6-pdr guns replaced (under Operation Whitehot[22]) by guns and mantlets from destroyed or scrapped Sherman tanks, fitted to Churchill IV cast turrets. Their performance was virtually identical to the VI. They were known as NA 75 from North Africa where the first conversions took place, after 48 Shermans with otherwise new guns had been disabled by mines.[23] Some IIIs were also modified, using IV turrets. To fit the Sherman mantlet required cutting away the front of the Churchill turret before it was welded in place, then the mantlet slot had to be cut away to give sufficient elevation. The Sherman 75 mm gun was designed for a left hand loader and the Churchill in common with British practice had a right hand loader. The gun was therefore turned upside down and the firing controls adapted.[24] The conversion of about 200 tanks was carried out between March–June 1944 and the conversion project earned the officer in charge, Capt. Percy Morrell, an MBE as well as promotion.

Specialist vehicles

Churchill Oke

A Churchill II or III with a flamethrower. The Oke flamethrowing tank was named after its designer, Major J.M. Oke. The design was basically for a Churchill tank fitted with the Ronson flamethrower equipment. A tank containing the flame fuel was fitted at the rear, with a pipe from it leading to the fixed angle mounting on the front hull to the left, leaving the hull machine gun unobstructed. There were three (named "Boar", "Beetle" and "Bull") present, in the first wave, at Dieppe which were quickly lost,[25] and abandoned.

Churchill AVRE (Armoured Vehicle Royal Engineers)

Churchill AVRE with fascine on tilt-forward cradle. This particular example is a post-WW2 AVRE on the MK VII chassis.

The Armoured Vehicle Royal Engineers was a Churchill III or IV equipped with the Petard, a 290 mm Spigot mortar, throwing the 40 lb (18 kg) "Flying dustbin" with its 28-pound high-explosive warhead; a weapon designed for the quick levelling of fortifications, which was developed by MD1. The petard was reloaded by traversing the turret to the co-driver's hatch. The co-driver then opens the petard barrel and pushes the petard round into the barrel and then closes it. The co-driver's hands are briefly exposed during the process. The AVRE was designed after the Canadian defeat at Dieppe, and could also be equipped with numerous other attachments, such as mine flails, fascine rollers, explosive placers etc. The crew of six were drawn from the Royal Engineers, except for the driver who came from the Royal Armoured Corps. One of the RE crew was a demolitions NCO sapper responsible for priming the "Flying dustbin" and who led the crew when they dismounted from the tank to place demolition charges ("Wade" charges).

By the invasion of France in June 1944, 180 AVREs had been converted. A further 574 followed.[26]

Post war Churchill AVREs were modified Churchill Mk VII armed with a breech loading low velocity 165mm demolition gun that fired a HESH round with about 40 lb of C4.

Churchill ARV (Armoured Recovery Vehicle)

Churchill ARV Mk II with front jib erected

Mk I – A turretless Mk I with a jib that could be fitted at front or rear. Production began in early 1942[27]

Mk II – A Churchill Mark III or Mark IV with a fixed turret/superstructure with a dummy gun. It was equipped for recovering other tanks from the battlefield. Mounted a front jib with a 7.5 ton capacity, a rear jib rated for 15 ton and winch that could pull 25 tons.[27] Crew was 3 with enough room to carry the crew of the tank being recovered. Armament was single Besa machine gun.

Churchill ARK (Armoured Ramp Carrier)

Churchill Ark Mk II (UK Pattern).
A Churchill tank of the North Irish Horse crossing the Senio in Italy on two stacked Churchill ARKs, Italy April 1945

A turretless Churchill with ramps at either end and trackways along the body to form a mobile bridge. Fifty of these were built on Mark II and Mark IV Churchills.[27] The Link Ark (or "Twin Ark") was two ARKs used side-by-side to give a wide crossing. The ramps on these were folding types giving a longer – 65 ft (20 m) – crossing.[28] This was used for the post war Conqueror heavy tank.

Ark Mk II had a wider (4 ft instead of 2 ft) trackway on the left hand side side so narrower vehicles could also use the ARK. These were conversions of the Ark Mark I in mid-1944. The "Italian Pattern" Ark Mk II ( initially called "Octopus") was produced in Italy using US ramps on Churchill Mk III chassis and did not have trackways on the tank itself (vehicles drove on the tank's tracks).[27]

"Lakeman Ark" was an experimental design for attacking very high obstacles. It was a turreted Churchill with the trackways built above the height of the turret, and long ramps at the rear.[29]

Churchill bridgelayer

A Churchill bridgelayer of 51st Royal Tank Regiment in action during a demonstration in the Mezzano area, 30 March 1945.

The British already had experience of bridge-laying tanks with the Valentine and Covenanter and began work on a Churchill-based bridge-layer in 1942. The bridge ("Tank, 30ft, No.2 ") which could support a weight of 60 tons was carried on top of the tank. When the obstacle was reached an arm (driven by hydraulics in the tank) pivoted at the front of the tank and placed the bridge in position.

Other bridges could be deployed by the Churchill. "Skid Bailey" was a bridge formed from Bailey Bridge parts on skids that was moved into position by two Churchill AVREs – one pulling and one pushing. "Mobile Bailey Bridge" was a complete bridge on unpowered track units; it was pushed into position by two AVREs. Similarly a bridge could be rested on an AVRE with its turret removed while a second AVRE pushed.[30]

Churchill Crocodile

Churchill Crocodile
Churchill Crocodile with the hooded flame projector ball-mounted in the hull front plate (no more than 800 Crocodile conversion kits were produced.[31])

The Churchill Crocodile was a Churchill VII which was converted by replacing the hull machine gun with a flamethrower. The fuel was in an armoured wheeled trailer towed behind. It could fire several 1 second bursts over 150 yards. The Crocodile was one of "Hobart's Funnies" – another vehicle used by the 79th Armoured Division. A working example can still be seen at the Cobbaton Combat Collection in North Devon.

Gun Carrier, 3in, Mk I, Churchill (A22D)

Gun Carrier in Dorset, 25 March 1943

(50) Coming out of a General Staff request in 1941 to investigate fitting high velocity guns tanks. Neither the Churchill or Valentine could mount a turret with anything larger than the 6-pdr but it was proposed that a fixed superstructure could carry a larger gun with limited traverse. Vauxhall were provided with 100 guns and given the task of producing the vehicle. The pilot vehicles were ready for testing in early 1942 and found to be satisfactory but progress with the 17-pdr Challenger cruiser tank and refocussing on a general purpose role (and 75mm gun) for the Churchill led to a reduced order. A fixed 88 mm (3.5 in) thick superstructure with the gun in a ball mount. The gun was an otherwise obsolete QF 3-inch 20 cwt anti-aircraft gun. Fifty were built in 1942 but none are known to have been used in combat- the 17 pounder anti-tank gun gave the British the necessary firepower. Some were adapted for experimentation and training with the "Snake" mine-clearing line charge device.[20]

Churchill Flail FV3902 or Toad

A post-war (1950s) mine-clearing flail tank built on a Churchill chassis using a Rolls-Royce Meteor engine to drive the flails.[32][33]

Churchill Goat

A chargelayer like the Double Onion device.

Churchill Great Eastern Ramp

A much larger longer and higher trackway ramp than the ARK for crossing 60 ft (18 m). The 25-foot long front ramps were launched into position with rockets.[29] Ten built and two delivered in 1945 but not used in action.[34]

Churchill Kangaroo

A postwar Churchill Kangaroo viewed from the rear corner

The Kangaroo was a Churchill hull converted to an armoured personnel carrier.

Designs based on chassis

In 1943 an attempt was made to produce a 17-pdr gun armed tank on the Churchill chassis. It was known that sufficient numbers of the 17-pdr Challenger cruiser were not going to be produced in time for the invasion of Europe, and work was only starting on the Centurion cruiser design. Due to the wider turret required, Vauxhall had to redesign the hull though it used as much of the Churchill Mark VII as possible. This resulted in the Tank, Infantry, Black Prince (A43). Six prototypes were built and delivered in May 1945 just as the European war was ending. The test programme was completed but the project was cancelled due to the emergence of the new and less complicated Centurion Mk1 which offered the same armament and armour and had just entered production.[35]


Preserved examples

Churchill IV preserved at The Tank Museum – Tankfest 2012

A number of Churchills still exist as gate guardians or war memorials, while many examples reside in museums.

The Churchill Tank Project is aiming to restore several key examples to original condition and working order: a Mk III* (converted to an AVRE, and recovered from a firing range[37]), a Mk IV (post-war conversion to a Twin-ARK[38]), and a Mk VII (recovered from a range in the North of England[39][40]). As of August 2014, the Mk III* and Mk IV are now complete – the only operational examples in the world – while restoration continues on the Mk VII.

The Tank Museum has a Churchill Flail FV3902, "Toad" in its collection. Another Toad was restored to full working condition in England and in May 2008 was acquired by Jacques Littlefield's Military Vehicle Technology Foundation in California.

See also


  1. ^ TOAD Flail in reserve for British Army until mid-1960s
  2. ^ who was also responsible for the triple differential design of the Merritt-Brown gearbox used in the Churchill
  3. ^ North Irish Horse, 51st Royal Tank Regiment and 142 (Suffolk) Regiment RAC
  1. ^ Churchill Tank (1983) page ix.
  2. ^ Fletcher p21
  3. ^ Perrett, p. 4
  4. ^ a b c
  5. ^ Fletcher p 21, p 58
  6. ^ a b "Fabrication of the new Churchill Tank, MK VII"
  7. ^ Fletcher p59
  8. ^ Churchill – vehicle history and specifications
  9. ^ Fletcher The Universal Tank
  10. ^ Perrett p15-16
  11. ^ KingForce
  12. ^ Perrett p17
  13. ^
  14. ^ , February 2012, p.3Tank Times"The Capture of Tiger 131",
  15. ^ Perrett p.11
  16. ^ "The Churchill in Australian Service" by Micheal Grieve
  17. ^ "Churchills shipped to Australia"
  18. ^ p. 389 Farrar-Hockley, Anthony (1990), Official History: The British Part in the Korean War, Volume I, London, England: HMSO, ISBN 0-11-630953-9
  19. ^ a b
  20. ^ a b c AFV Profile
  21. ^ New Vanguard p6
  22. ^
  23. ^ Fletcher Universal Tank, pp. 25–26
  24. ^ Perrett, p. 9
  25. ^ Perrett p16
  26. ^ Chamberlain & Ellis (1969) p70
  27. ^ a b c d Chamberlain & Ellis (1969) p70
  28. ^ [1] Archived 1 February 2009 at the Wayback Machine
  29. ^ a b Chamberlain & Ellis (1969) p73
  30. ^ Chamberlain & Ellis (1969) p72-73
  31. ^ Delaforce p. 71
  32. ^
  33. ^
  34. ^
  35. ^ Chamberlain & Ellis (1969) p 77
  36. ^ Rulers of Iraq and Saudi Arabia bury an old feud with big party in Baghdad. LIFE Magazine: May 27, 1957.
  37. ^
  38. ^
  39. ^
  40. ^


  • Churchill Tank – Vehicle History and Specifications 1983 HMSO ISBN 0-11-290404-1

External links

  • The Churchill Tank Project – aiming to restore a Mk III, Mk, IV, and Mk VII.
  • Armour in Focus A22
  • Henk of Holland
  • OnWar specifications: Churchill I Churchill IV Churchill VII
  • Development of the Churchill
  • A20 developmental history
  • WWII Vehicles
  • Churchills in Soviet Union
  • "Churchill" Heavy Infantry Tank in the Russian Battlefield
  • Detailed vehicle description at 9th Battalion, Royal Tank Regiment website
  • Detailed history of the 9th Battalion, using Churchills from introduction to war's end
  • Memories of Frank Meredith, 9th Battalion Driver/Mechanic 1942–1945
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.