World Library  
Flag as Inappropriate
Email this Article

Flexible mold

Article Id: WHEBN0002460468
Reproduction Date:

Title: Flexible mold  
Author: World Heritage Encyclopedia
Language: English
Subject: Flexible, Plastics industry, Casting (metalworking), Plastic
Collection: Plastics Industry
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Flexible mold

A mold is a hollow shape which exactly encloses the shape of a desired object. The object is usually created by pouring a liquid into the mold and allowing it to solidify: typical liquids include molten metal or plastic, plaster of Paris, epoxy resin.

Molds generally divide into two classes: solid or flexible.

There are five different types of flexible mold compounds in significant use today.

Contents

  • Hot-Melt 1
  • Latex 2
  • Silicone rubbers 3
  • Polysulfide rubbers 4
  • Polyurethane flexible mold compounds 5
  • Equipment and accessories 6

Hot-Melt

polyvinyl chloride

  • inexpensive, worn molds can be melted and recast.
  • hazardous to handle due to high temperatures required for melting.
  • use limited to model and pattern materials that are heat resistant.

Latex

  • produces a very elastic, thin-walled, strong mold
  • shrinkage is high
  • molds must be supported to prevent distortion.
  • 10 to 20 brush coats must be applied for adequate thickness, with time allowed to "dry" in between each coat, making the mold is slow and time consuming.

Silicone rubbers

  • excellent molds for casting resins and foams
  • material cost is extremely high.

Polysulfide rubbers

  • versatile and are especially useful for casting plaster, Hydrocal, and other water mixed cements.
  • can be used for casting wax candles and some limited use for resin casting.
  • easy to handle, non-adhesive and can be poured over clay or practically any type of model or pattern, using very simple release agents such as soap or Vaseline.
  • can be used to take impressions directly from a waterclay or plastelene model, so that permanent master models can then be cast in plaster or Hydrocal.

Polyurethane flexible mold compounds

  • limited shelf stability
  • "moisture conscious"
  • easy to handle with simple mixing ratios and good fluidity.
  • can be used for pouring practically any type of cementitious material, casting resin or foam formulation.
  • Cost of material is far below that of the silicones and appreciably lower than polysulfides.

From the standpoint of general utility and economy, the polyurethanes surpass all other types.

Equipment and accessories

Mixing containers and stirring paddles should be of metal or plastic and always spotlessly clean, warm and dry. Use 1-inch fiber brushes cut down to 1-inch length for application of wax release agent. A regular short fiber scrubbing brush should be used for buffing wax from deep grain or fine design of model or pattern.

Sulphur Free Plastalina Clay (The Compleat Sculptor, New York City) is excellent for modeling, laying up and sealing models and dams. 1/4"-3/8" plywood should be used for mounting models. Scrap pieces can be sawed to rectangular shapes and used for straight side retaining dams.

Lightweight sheet metal, linoleum and heavy cardboard can be used for circular or irregular shaped retaining walls. Sash cord and masking tape are used to bind the walls to the model baseboard. 1/2" X 2" furring and "2 x 4's" cut to short lengths make good wedges. For plaster casting, use regular Molding or Casting Plaster

This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 



Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.