World Library  
Flag as Inappropriate
Email this Article

Unity (ISS module)


Unity (ISS module)

The Unity module as seen in December 1998
Station statistics
NSSDC ID: 1998-069F
Launch date: 4 December 1998
Launch vehicle: Space Shuttle Endeavour
Permanently docked: 6 December 1998
Mass: 11,612 kilograms (25,600 lb)
Length: 5.47 metres (17.9 ft)
Diameter: 4.57 metres (15.0 ft)
References: [1][2]
The Unity module as seen in May 2011

The Unity connecting module was the first U.S.-built component of the International Space Station. It is cylindrical in shape, with six berthing locations (forward, aft, port, starboard, zenith, and nadir) facilitating connections to other modules. Unity measures 4.57 metres (15.0 ft) in diameter, is 5.47 metres (17.9 ft) long, and was built for NASA by Boeing in a manufacturing facility at the Marshall Space Flight Center in Huntsville, Alabama. Sometimes referred to as Node 1, Unity was the first of the three connecting modules; the other two are Harmony and Tranquility.


  • Launch and initial berthing 1
  • Connections to other station components 2
  • Details 3
  • Other nodes 4
  • Footnotes 5
  • References 6

Launch and initial berthing

Unity was carried into orbit as the primary cargo of the Space Shuttle Endeavour on STS-88, the first Space Shuttle mission dedicated to assembly of the station. On December 6, 1998, the STS-88 crew mated the aft berthing port of Unity with the forward hatch of the already orbiting Zarya module. (Zarya was a mixed Russian-US funded and Russian-built component launched earlier aboard a Russian Proton rocket from Baikonur, Kazakhstan.) This was the first connection made between two station modules.

Connections to other station components

Unity has 2 axial, and 4 radial Common Berthing Mechanism (CBM) ports. In addition to connecting to the Zarya module, Unity connects to the U.S. Destiny Laboratory Module (added on STS-98), the Z1 truss (an early exterior framework for the station added on STS-92), the PMA-3 (also added on STS-92), and the Quest Joint Airlock (added on STS-104). In addition, the Leonardo and Raffaello Multi-Purpose Logistics Modules were each berthed to Unity on multiple missions. During STS-120 the Harmony connecting module was temporarily berthed to the port-side hatch of Unity. Tranquility, with its multi-windowed cupola, was attached to Unity's port side during the STS-130 mission, and PMM Leonardo was added to the nadir hatch during STS-133.


Interior of the Unity module

Essential space station resources such as fluids, environmental control and life support systems, electrical and data systems are routed through Unity to supply work and living areas of the station. More than 50,000 mechanical items, 216 lines to carry fluids and gases, and 121 internal and external electrical cables using six miles of wire were installed in the Unity node. Unity is made of aluminum.

Prior to its launch aboard Endeavour, conical Pressurized Mating Adapters (PMAs) were attached to the aft and forward berthing mechanisms of Unity. Unity and the two mating adapters together weighed about 25,600 pounds (11,600 kg). The adapters allow the docking systems used by the Space Shuttle and by Russian modules to attach to the node's hatches and berthing mechanisms. PMA-1 now permanently attaches Unity to Zarya, while PMA-2 provided a Shuttle docking port. Attached to the exterior of PMA-1 are computers, or multiplexer-demultiplexers (MDMs), which provided early command and control of Unity. Unity also is outfitted with an early communications system that allows data, voice and low data rate video with Mission Control Houston, to supplement Russian communications systems during the early station assembly activities. PMA-3 was attached to Unity's nadir berthing mechanism by the crew of STS-92.

Other nodes

Node 3 (Tranquility) in space

The two remaining station connecting modules, or nodes, were built in Italy by Alenia Aerospazio, as part of an agreement between NASA and the European Space Agency (ESA). Harmony (formerly known as Node 2) and Tranquility (formerly known as Node 3) are slightly longer than Unity, measuring almost 6.4 meters (21 feet) long in total. In addition to their six berthing ports, each can hold eight International Standard Payload Racks (ISPRs). Unity, in comparison, holds just four ISPRs. ESA built Nodes 2 and 3 as partial payment for the launch aboard the Shuttle of the Columbus laboratory module, and other ESA equipment.


  1. ^ "NASA - NSSDC - Spacecraft - Details". Retrieved 8 November 2013. 
  2. ^ "Unity Node". NASA. Retrieved 8 November 2013. 


  • NASA Facts: Unity Connecting Module: cornerstone for a Home in Orbit NASA, January 1999
  • Expedition 15 - Tour of the Unity Node filmed in July 2007 by Clayton Anderson
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.