World Library  
Flag as Inappropriate
Email this Article

Voltage divider

Article Id: WHEBN0000393519
Reproduction Date:

Title: Voltage divider  
Author: World Heritage Encyclopedia
Language: English
Subject: Linear regulator, Potentiometer, Attenuator (electronics), Multimeter, Holiday lighting technology
Collection: Analog Circuits
Publisher: World Heritage Encyclopedia

Voltage divider

Figure 1: A simple voltage divider

In electronics, a voltage divider (also known as a potential divider) is a passive linear circuit that produces an output voltage (Vout) that is a fraction of its input voltage (Vin). Voltage division is the result of distributing the input voltage among the components of the divider. A simple example of a voltage divider is two resistors connected in series, with the input voltage applied across the resistor pair and the output voltage emerging from the connection between them.

Resistor voltage dividers are commonly used to create reference voltages, or to reduce the magnitude of a voltage so it can be measured, and may also be used as signal attenuators at low frequencies. For direct current and relatively low frequencies, a voltage divider may be sufficiently accurate if made only of resistors; where frequency response over a wide range is required (such as in an oscilloscope probe), a voltage divider may have capacitive elements added to compensate load capacitance. In electric power transmission, a capacitive voltage divider is used for measurement of high voltage.


  • General case 1
  • Examples 2
    • Resistive divider 2.1
    • Low-pass RC filter 2.2
    • Inductive divider 2.3
    • Capacitive divider 2.4
  • Loading effect 3
  • Applications 4
    • Sensor measurement 4.1
    • High voltage measurement 4.2
    • Level shifting 4.3
  • References 5
  • See also 6
  • External links 7

General case

A voltage divider referenced to ground is created by connecting two electrical impedances in series, as shown in Figure 1. The input voltage is applied across the series impedances Z1 and Z2 and the output is the voltage across Z2. Z1 and Z2 may be composed of any combination of elements such as resistors, inductors and capacitors.

If the current in the output wire is zero then the relationship between the input voltage, Vin, and the output voltage, Vout, is:

V_\mathrm{out} = \frac{Z_2}{Z_1+Z_2} \cdot V_\mathrm{in}

Proof (using Ohm's Law):

V_\mathrm{in} = I\cdot(Z_1+Z_2)
V_\mathrm{out} = I\cdot Z_2
I = \frac {V_\mathrm{in}}{Z_1+Z_2}
V_\mathrm{out} = V_\mathrm{in} \cdot\frac {Z_2}{Z_1+Z_2}

The transfer function (also known as the divider's voltage ratio) of this circuit is:

H = \frac {V_\mathrm{out}}{V_\mathrm{in}} = \frac{Z_2}{Z_1+Z_2}

In general this transfer function is a complex, rational function of frequency.


Resistive divider

Figure 2: Simple resistive voltage divider

A resistive divider is the case where both impedances, Z1 and Z2, are purely resistive (Figure 2).

Substituting Z1 = R1 and Z2 = R2 into the previous expression gives:

V_\mathrm{out} = \frac{R_2}{R_1+R_2} \cdot V_\mathrm{in}

If R1 = R2 then

V_\mathrm{out} = \frac{1}{2} \cdot V_\mathrm{in}

If Vout=6V and Vin=9V (both commonly used voltages), then:

\frac{V_\mathrm{out}}{V_\mathrm{in}} = \frac{R_2}{R_1+R_2} = \frac{6}{9} = \frac{2}{3}

and by solving using algebra, R2 must be twice the value of R1.

To solve for R1:

R_1 = \frac{R_2 \cdot V_\mathrm{in}}{V_\mathrm{out}} - R_2 = R_2 \cdot ({\frac{V_\mathrm{in}}{V_\mathrm{out}}-1})

To solve for R2:

R_2 = R_1 \cdot \frac{1} {({\frac{V_\mathrm{in}}{V_\mathrm{out}}-1})}

Any ratio Vout/Vin greater than 1 is not possible. That is, using resistors alone it is not possible to either invert the voltage or increase Vout above Vin.

Low-pass RC filter

Figure 3: Resistor/capacitor voltage divider

Consider a divider consisting of a resistor and capacitor as shown in Figure 3.

Comparing with the general case, we see Z1 = R and Z2 is the impedance of the capacitor, given by

Z_2 = -\mathrm{j}X_{\mathrm{C}} =\frac{1}{\mathrm{j} \omega C} \ ,

where XC is the reactance of the capacitor, C is the capacitance of the capacitor, j is the imaginary unit, and ω (omega) is the radian frequency of the input voltage.

This divider will then have the voltage ratio:

\frac{V_\mathrm{out}}{V_\mathrm{in}} = \frac{Z_\mathrm{2}}{Z_\mathrm{1} + Z_\mathrm{2}} = \frac{\frac{1}{\mathrm{j} \omega C}}{\frac{1}{\mathrm{j} \omega C} + R} = \frac{1}{1 + \mathrm{j} \omega R C} \ .

The product τ (tau) = RC is called the time constant of the circuit.

The ratio then depends on frequency, in this case decreasing as frequency increases. This circuit is, in fact, a basic (first-order) lowpass filter. The ratio contains an imaginary number, and actually contains both the amplitude and phase shift information of the filter. To extract just the amplitude ratio, calculate the magnitude of the ratio, that is:

\left| \frac{V_\mathrm{out}}{V_\mathrm{in}} \right| = \frac{1}{\sqrt{1 + (\omega R C)^2}} \ .

Inductive divider

Inductive dividers split AC input according to inductance:

V_\mathrm{out} = \frac{L_2}{L_1 + L_2} \cdot V_\mathrm{in}

The above equation is for non-interacting inductors; mutual inductance (as in an autotransformer) will alter the results.

Inductive dividers split DC input according to the resistance of the elements as for the resistive divider above.

Capacitive divider

Capacitive dividers do not pass DC input.

For an AC input a simple capacitive equation is:

V_\mathrm{out} = \frac{C_1}{C_1 + C_2} \cdot V_\mathrm{in}

Any leakage current in the capactive elements requires use of the generalized expression with two impedances. By selection of parallel R and C elements in the proper proportions, the same division ratio can be maintained over a useful range of frequencies. This is the principle applied in compensated oscilloscope probes to increase measurement bandwidth.

Loading effect

The output voltage of a voltage divider will vary according to the electric current it is supplying to its external electrical load. To obtain a sufficiently stable output voltage, the output current must either be stable or limited to an appropriately small percentage of the divider's input current. Load sensitivity can be decreased by reducing the impedance of the divider, though this increases the divider's quiescent input current and results in higher power consumption (and wasted heat) in the divider. Voltage regulators are often used in lieu of passive voltage dividers when it is necessary to accommodate high or fluctuating load currents.


Voltage dividers are used for adjusting the level of a signal, for bias of active devices in amplifiers, and for measurement of voltages. A Wheatstone bridge and a multimeter both include voltage dividers. A potentiometer is used as a variable voltage divider in the volume control of many radios.

Sensor measurement

Voltage dividers can be used to allow a microcontroller to measure the resistance of a sensor.[1] The sensor is wired in series with a known resistance to form a voltage divider and a known voltage is applied across the divider. The microcontroller's analog-to-digital converter is connected to the center tap of the divider so that it can measure the tap voltage and, by using the measured voltage and the known resistance and voltage, compute the sensor resistance.

High voltage measurement

High voltage resistor divider probe.

A voltage divider can be used to scale down a very high voltage so that it can be measured by a volt meter. The high voltage is applied across the divider and the divider output—which has a lower voltage that is within the meter's input range—is measured by the meter. High voltage resistor divider probes designed specifically for this purpose can be used to measure voltages up to 100 kV. Special high-voltage resistors are used in such probes as they must be able to tolerate high input voltages and, to produce accurate results, must have matched temperature coefficients and very low voltage coefficients. Capacitive divider probes are typically used for voltages above 100 kV, as the heat caused by power losses in resistor divider probes at such high voltages could be excessive.

Level shifting

A voltage divider can be used as a level shifter to safely interface different circuits which use different reference voltages. For example, an Arduino microcontroller works at 5 V logic, while many sensors require 3.3 V logic. Directly interfacing the Arduino with a 3.3 V sensor may cause permanent damage to the sensor. By using a level shifter with a ratio of 3.3/5 resistor values on each pin connected to the sensor, an Arduino board can safely communicate with the sensor.


  1. ^ "A very quick and dirty introduction to Sensors, Microcontrollers, and Electronics". Retrieved 29 October 2013. 

See also

External links

  • Voltage and Current Dividers: What They Are and What They Do
  • SparkFun voltage divider tutorial
  • Voltage divider tutorial video in HD
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.