World Library  
Flag as Inappropriate
Email this Article

Metrication in Australia


Metrication in Australia

Metrication in Australia effectively began in 1966 with, the successful conversion to decimal currency, under the auspices of the Decimal Currency Board.[1] The conversion of measurements—metrication—commenced subsequently in 1971, under the direction of the Metric Conversion Board and actively proceeded until the Board was disbanded in 1981.

Before 1970, Australia mostly used the imperial system for measurement, which the Australian colonies had inherited from the United Kingdom. Between 1970 and 1988, imperial units were withdrawn from general legal use and replaced with SI metric units, facilitated through legislation and government agencies. SI units are now the sole legal units of measurement in Australia. Australia's largely successful transition to the metric system contrasts with the ongoing opposition to metrication in the United States, Canada, and the United Kingdom.


  • History 1
    • Metrication of horse racing 1.1
    • Metrication of weather reporting and forecasts 1.2
    • Metrication of the road signs 1.3
    • Building and construction 1.4
  • Extent 2
  • Notes 3
  • References 4
  • Further reading 5


Although there was debate in Australia's first Parliament after federation to consider adopting the metric system,[2] metric units first became legal for use in Australia in 1947 when Australia signed the Metre Convention (or Convention du Mètre). However, Imperial "Weights and Measures" were most commonly used until the Commonwealth government began the metric changeover in the 1970s. In 1960, SI units were adopted as a worldwide system of measurement by international agreement at the General Conference on Weights and Measures. The metre, kilogram, second, ampere, kelvin,[nb 1] candela and mole were defined as base units in this system and units formed from combinations of these base units were known as "derived units". SI units were subsequently adopted as the basis for Australia's measurement standards, whereby they were defined as Australia's legal units of measurement.[3]

In 1968, a Select Committee of the Australian Senate examined metric "Weights and Measures" and came to the unanimous conclusion that it was both practical and desirable for Australia to change to the metric system. Some of their considerations included the "inherent advantages of the metric system" that meant that weighing and measuring was facilitated, "often with substantial increases in efficiency". Educationally, the reform would "simplify and unify the teaching of mathematics and science, reduce errors, save teaching time and give a better understanding of basic physical principles". In 1968, more than 75% of Australia's exports went to metric countries, and at that time it was noted that all countries except the United States were metric or were converting to the metric system. It was also noted that because of Australia's large migrant programme, more than 10 per cent of people over 16 years of age had used the metric system before coming to Australia. They also noted that school pupils were widely familiar with the metric system because it had been taught in the schools for many years.[4]

By 1968, metrication was already well under way in Australian industry. The pharmaceutical industry had metricated in 1965 and much of the chemical and electronics industries worked in metric units—there being no "Imperial" units for the latter. One of the country's major automobile manufacturers had already declared its intention to metricate before the Government announced its decision to change to the metric system. "The change itself provided a unique opportunity to rationalise and modernise industrial practices and bring Australia's technical standard specifications into accord with those adopted internationally".[4]

On 12 June 1970, the Australian the Metric Conversion Act passed by the Australian Parliament was given assent. This Act created the Metric Conversion Board to facilitate the conversion of measurements from imperial to metric. A timeline of major developments in this conversion process is as follows:[2]

The Metric Conversion Board spent A$5.955 million during its 11 years of operation, and the federal government distributed $10 million to the states to support their conversion process. The cost of metrication for the private sector was not determined but the Prices Justification Tribunal reported that metrication was not used to justify price increases.[7]

Opposition to metrication was not widespread.[7] The Metric Conversion Board did not proceed with education programmes as polling revealed that most people were learning units and their application independently of each other, rendering efforts to teach the systematic nature of the metric system unnecessary and possibly increasing the amount of opposition.[7]

The Metric Conversion Board was dissolved in 1981, but the conversion to the metric system was not completed until 1988. Between 1984 and 1988, the conversion was the responsibility of the National Standards Commission, later renamed the National Measurement Institute. In 1987, real estate became the last major industry to convert, and, in 1988, the few remaining imperial units were removed from general use.

Restrictions of volume and masses that had previously compelled manufacturers to package products to rounded imperial sizes despite metric labelling, for example packaging a soft drink can as a rounded 13 imp fl oz but labelling it as 375 ml, were removed in 2008.

Metrication of horse racing

An early change was the metrication of horse racing. This was facilitated because the furlong (one eighth of a mile) is close to 200 m. Therefore, the Melbourne Cup was changed from 2 miles (about 3,218 m) to 3,200 m. The first metric Melbourne Cup was raced in November 1972.[8]

Metrication of weather reporting and forecasts

When the Australian Bureau of Meteorology was enlisted to introduce the metric system for weather reporting and forecasts, its public relations officer, Godfrey Wiseman, coined a series of jingles to educate the public, using the terms "frosty fives", "tingling tens", "temperate twenties", "thirsty thirties" and "fiery forties" to describe human sensation to temperatures in degrees Celsius. This was very successful because the public soon became aware of the significance of the descriptions.

As the culmination of this campaign, weather reports and forecasts in both Imperial and metric measures were only provided for one month. After that, purely metric measurements were used for temperature, wind speed, rainfall, air pressure and other meteorological phenomena.[9]

Metrication of the road signs

An important and very visible sign of metric conversion in Australia was the change in road signs and the accompanying traffic regulations; "M-day" for this change was 1 July 1974. Because of careful planning, almost every road sign in Australia was converted within a month. This was achieved by installing covered metric signs alongside the imperial signs before the change and then removing the imperial sign and uncovering the metric sign during the month of conversion.

While road signs could not all be changed at the same time, there was little chance of confusion as to what any speed limit sign meant during this short change-over period. This was because the previous (MPH) signs had the signage in black on white and were rectangular, in the same style as current US speed limit signs, while the (km/h) signs which replaced them had the number indicating the speed limit inside a red circle, as is done in Europe.[10]

Road distance signs were also converted during this period. To avoid confusion as to whether the distance indicated was in miles or kilometres all the new kilometre signs had affixed to them a temporary yellow plate, on which was indicated the corresponding number of miles. These temporary plates were removed after about one year.

Except for bridge-clearance and flood-depth signs, dual marking was avoided. Though people opposed to metrication expressed the fear that ignorance of the meaning of metric speeds would lead to slaughter on the roads, this did not happen as most drivers under the age of 25 had been taught metric units at school and through them, their parents were familiar with metric speeds if not metric units as a whole.

It was believed that public education would be the most effective way of ensuring public safety. A Panel for Publicity on Road Travel, made up of the various motoring organisations, regulatory authorities and the media, planned a campaign to publicise the change. The resulting publicity campaign cost $200,000 and the Australian Government Department of Transport paid for it. The Board also produced 2.5 million copies of a pamphlet, "Motoring Goes Metric". This was distributed through post offices, police stations and motor registry offices.

"For about a year before the change, motor car manufacturers fitted dual speedometers to their vehicles and, after 1974, all new cars were fitted with metric-only speedometers. Several kinds of speedometer conversion kits were available.

"As a result of all these changes, conversion on the roads occurred without incident."[11][12]

Building and construction

The building industry was the first major industry grouping in Australia to complete its change to metric. This was achieved within two years by January 1976 for all new buildings other than those for which design had commenced well before metrication began. The resulting savings for builders and their sub-contractors has been estimated at about 10% a year of gross turnover.[13]

In this the industry was grateful to the SAA (now ISO, where this decision had already been taken.

This was formally stated as follows: "The metric units for linear measurement in building and construction will be the metre (m) and the millimetre (mm), with the kilometre (km) being used where required. This will apply to all sectors of the industry, and the centimetre (cm) shall not be used. … the centimetre should not be used in any calculation and it should never be written down".[14]

The logic of using the millimetre in this context was that the metric system had been so designed that there would exist a multiple or submultiple for every use. Decimal fractions would not have to be used. Since the tolerances on building components and building practice would rarely be less than one millimetre, the millimetre became the sub-unit most appropriate to this industry.

Although for the most part they are ignored in everyday life, it was not possible for education in the logical construction of the metric system to ignore the metric prefixes deci, centi, hecto and deka, since the derivation of the litre is dependent upon the knowledge that it derives from the volume of a cubic decimetre, i.e. 1000 cubic centimetres.

However, in Australia, the prefix "centi" has been limited to use with the metre (mainly by the general public not associated with the building industry)—unlike in Europe, where the centilitre may often be encountered.


Metrication is mostly complete. Road signs are totally metric, as are the speedometers and odometers in motor vehicles and the sale of oil and petrol is by the litre. Vehicle tyre pressures are still commonly talked about in pounds per square inch.[15][16]

Fruit and vegetables are advertised, sold and weighed by the kilogram, groceries are packed and labelled in metric measures. Schooling is wholly metric. Newspaper reports are mostly in metric terms. In some cases old imperial standards were replaced with rounded metric values, as with horse racing or the size of beer glasses (rounded to the nearest 5 mL). The pre-metric names of beer glass sizes, including the pint, have been retained (although in South Australia the "pint" of beer is not an imperial pint, as it is elsewhere in Australia). Dressed timber is often sold in lengths such as 1.8, 2.1, 2.4, 3.0 and 3.6 metres, each multiples of 300 mm, thereby approximating foot length increments,[17] while pipes and conduits may be specified as having diameters of 12, 19, 25 and 32 etc. mm   (based on "soft" conversions" of 12, 34, 1 and 1 14 in).

In some cases goods manufactured to pre-metric standards are available, such as some bolts, nuts, screws[18][19] and pipe threads[20] and there are some instances where pre-metric measures may still be used:

  • Mass is referred to in kilograms,[21][22] and baby nappy sizes are specified in kilograms only.[23][24] While some parents may still convert their baby's hospital-stated birth mass to pounds and ounces, the practice of using pre-metric units has become far less common.[25]
  • Height is measured and given in centimetres.[21][26] In informal and private contexts a person's height is still sometimes stated in feet and inches.[27][28]
  • Domestic and commercial real estate is advertised in square metres or hectares but though crop yields are described in tonnes per hectare,[29] rural land areas are sometimes still advertised in acres.[30]
  • Weather reports are always in metric terms[31] but some specialised surf reports give wave heights in feet[32] and there are occasional references to "the old century", meaning 100 °F, when describing temperatures of 38 °C or more.[33]

Imperial measurements are used in preference to metric usually where the product originates from or is intended for an American market (printers, hard-disk drives) or when the size increment for a product is a multiple of an inch (televisions and tyres). A few examples are:

  • Scuba diving uses metric measures[34] but the altitude for sky diving is routinely is given in feet.[35][36]
  • Aviation, as in many other metric countries, specifies horizontal distances in nautical miles and horizontal speed in knots, but horizontal distance for visibility or clearance from clouds is in kilometres or metres, as are runway dimensions. (The pressure and temperature are also given in SI units, in hectopascals and degrees Celsius respectively). Height or altitude is always specified in feet, as this is vital for safety—as long as one remaining country in the world does not change to metric measurements. (The error in approximating 1000 feet as 300 metres is 4.8 m/16.75 feet. This may be somewhat insignificant at low altitudes. However, the cumulative effect of this error by 30,000 feet (9.15 km) becomes quite significant (144 m/472 feet) The measurement and vertical speed (rate of climb or descent) is given in feet per minute—for much the same reasons height is given in feet.
  • Australia uses metric paper sizes for office use and home printing. (A4 = 210 × 297 mm)[37] However, the term dots per inch (dpi) is still used when printing images.[38] The photo printing industry usually uses imperial sizes for photo dimensions (e.g. 4 × 6 inch rather than 10 × 15 cm).
  • Historical writing and presentations may include pre-metric units to reflect the context of the era represented.
  • Vehicle tyres (as in the rest of the world) mark the rim diameter in inches and the width in millimetres. A car tyre marked '165/70R13' has a width of 165 mm, an aspect ratio (profile) of 70% and a 13-inch rim diameter. Tyre pressures may be given in both kilopascals and "pounds per square inch".[39]
  • TV screens and LCD monitors may be described in inches instead of or as well as centimetres, e.g., a Plasma screen may be advertised as 42 inches (106 centimetres), and a computer monitor screen may be advertised in inches.
  • Advertising billboards are measured by feet—because of the still pervading influence of USA practices on such activities.

The cultural transmission of British and American English in Australia has also been noted to be a cause for residual use of Imperial units of measure.[7]


  1. ^ The kelvin was known as the degree Kelvin at the time.


  1. ^ Dollar Bill" Currency Conversion Advertisement—1966""". Video. Commonwealth of Australia—Sound and Film Archive. 
  2. ^ a b "History of Measurement in Australia". Australia's Measurement System. National Measurement Institute. Retrieved 16 October 2010. 
  3. ^ "How Australia's measurement system works". Australia's Measurement System. National Measurement Institute. Retrieved 21 November 2009. 
  4. ^ a b "Introduction of the metric system in Australia Support for the change". Government of Western Australia. 4 March 2010. Retrieved 8 May 2010. 
  5. ^ "Australia ACORN-SAT temperature fraction audit". web page. WA climate net. December 2009. Retrieved 4 December 2012. 
  6. ^ Metric conversion ad - 1974 YouTube.
  7. ^ a b c d "Metrication of Australia". Metric usage and metrication in other countries. U.S. Metric Association. 1996–2009. Retrieved 26 November 2009. 
  8. ^ "Melbourne Cup History". Aussie Punter. Retrieved 2 August 2011. 
  9. ^ "Wording and Verification of Forecasts". Federation and Meteorology. Australian Science and Technology Heritage Centre. Retrieved 2015-07-30. 
  10. ^ "Road Metric Conversion Advertisement—1974". Video. Commonwealth of Australia—Sound and Film Archive. 
  11. ^ Kevin Wilkes (1992). "Metrication in Australia". Book. Commonwealth of Australia. Retrieved 17 February 2011A quotation from the book appears at the link provided 
  12. ^ Kevin Wilkes (1992). "Metrication in Australia" (PDF). Book. Commonwealth of Australia,Entire document. 
  13. ^
  14. ^ (Standards Association of Australia "Metric Handbook, Metric Conversion in Building and Construction" 1972)
  15. ^
  16. ^
  17. ^
  18. ^ admin, on 27 August 2009 (27 August 2009). "what screw size and thread measurement do we use for hardware? | the scrooz blog". Retrieved 2 August 2011. 
  19. ^ "Nuts and Bolts - Industrial Size Assortment Packs of Hi-Tensile Nuts & Bolts". Retrieved 2 August 2011. 
  20. ^ "Pipe Thread, Tapered Screw Plug and Screw Ring Gauges". Retrieved 2 August 2011. 
  21. ^ a b "Profiles of Health, Australia, 2011-13".  
  22. ^
  23. ^ "Nappies product range - Find advice on baby products at". Retrieved 2 August 2011. 
  24. ^ "Snugglers® Australia - Our Products". Retrieved 2 August 2011. 
  25. ^ An example where some birth masses are given in pounds and ounces.
  26. ^ Beth Price, David Tynan, Natalie Caruso, Allason McNamara, Gloria Stillman, Jill Brown (2009). MathsWorld Year 8 VELS Edition. Australia:  
  27. ^ "Kawasaki Sportsbike Riders Club - Australia - Online Forum • View topic - ZZR 600 Seat Height Question". Retrieved 2 August 2011. 
  28. ^ At least one Australian internet dating service uses imperial units for height (with metric equivalents in brackets) but people are unable to select height in raw metric figures.
  29. ^ "High hopes for big crop yields - ABC News (Australian Broadcasting Corporation)". 17 November 2010. Retrieved 2 August 2011. 
  30. ^ "NSW". Retrieved 2 August 2011. 
  31. ^ "Sydney Weather". The Sydney Morning Herald. 
  32. ^ Tatnell, Paul (17 September 2010). "Australian monster wave heralds huge surf for Sydney". The Sydney Morning Herald. 
  33. ^ "The 7.30 Report". ABC. 12 November 2009. Retrieved 2 August 2011. 
  34. ^ "Litres, metres and bar - Diving with the metric system in Australia | ex HMAS Canberra Reef". Retrieved 2 August 2011. 
  35. ^ "Skydive Jump The Beach Mission Beach Queensland Australia Freefall Tandem Solo Courses". Retrieved 2 August 2011. 
  36. ^ "Parachutes Australia". Parachutes Australia. Retrieved 2 August 2011. 
  37. ^ IMS. "Sydney Australia Ph: 1300 556 744 Paper & Envelope Sizes". Network Printing. Retrieved 2 August 2011. 
  38. ^ "Label Printers - Products - QL Label Printers - Brother ® Australia". Retrieved 2 August 2011. 
  39. ^ "Bridgestone [Australia] Tyre pressure tips". web page. Bridgestone Australia Corporate. 2007. Retrieved 4 June 2011. 

Further reading

  • Wilks, K.J (1992). Metrication in Australia: a review of the effectiveness of policies and procedures in Australia's conversion to the metric system (PDF). Canberra: Department of Industry, Technology and Commerce, Australian Government Publishing Service.  
  • "Significant achievements and the history of measurement in Australia". Department of Industry, Tourism and Resources - National Measurement Institute. Retrieved 9 June 2006. 
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Hawaii eBook Library are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.